So for each of the binding edge types, ensuring I had "Last Used Settings" selected, I then selected the "Save Current Settings as Preset." option in the Presets list, and gave it a name based on the Long Edge/Short Edge option I had most recently performed a print with. Selecting each of those options, I printed a blank page to the printer, and then in the regular print options dialog select the Presets List, I selected "Last Used Settings" and noticed that when selecting "View Presets" under that menu, that 2-sided printing was selected (even though the option in the Layout page was still disabled). Within the options presented in that section is "2-sided Printing" and Binding Edge radio button options to select either "2-sided Long Edge" or "2-sided Short Edge" I found that in my old MS Office Word, the printer dialog has some additional options, one of them being "2-sided Printing Settings". Like others, my "Two-sided" selection list is disabled. Then every time you want to print that way just select this option you've called 2-sided from this drop down menu in Presets. This will ensure you don't double sided print everything! Again in this same menu select 'Show Presets' and tick 'Reset Presets Menu to "Default Settings" After Printing. Select 'Save current settings as Preset' & name it anything you want.
Go to Presets under Printer at the top of the screen & drop downĦ. (Don't need to worry about the '2nd Two Sided Printing' right above this. Scroll further down to Duplex Tumble & select DuplexNoTumble. Scroll down to 2-sided Printing and change to 'on'Ĥ. Drop down 'Preview' and select Printer Featuresģ. Select print to bring up the print menuĢ. Printer is Epson WF3640 that 'used to' print double sided. 'bizhub C452', 'bizhub C552/C552DS', 'bizhub C652/C652DS' Konica Minolta products received high marks from the BLI rigorous laboratory evaluation tests in key areas that mattered most to end users - reliability, ease of use, productivity, image quality and a host of connectivity attributes.
#Double sided grayed out bizhub c452 pro
I'm on a 2017 MacBook Pro with Majave 10.14.3 8 Change imaging unit - 9 PRCB ICP1 or ICP2 conduction check - 10 Change PRCB.'2 Sided' greyed out and off when you drop down Layout? This will fix it. 2 Clean the TCR sensor window on the underside of the imaging unit if dirty - 3 Reinstall imaging unit - 4 Reinstall toner cartridge - 5 M9, M10, M11 operation check (At this time, IU must be non-installation.) M9: PRCB CN19-1 to 4 M10: PRCB CN19-5 to 8 M11: PRCB CN19-9 to 12 C-21 6 M13, M14 operation check M13: PRCB CN20-5 to 8 M14: PRCB CN20-9 to 12 K-6 7 If the toner empty sensor and its surroundings inside the sub hopper are dirtied with toner, clean them. Remedy: 1 Perform image troubleshooting procedure if image density is low.Causes: Imaging unit /C Imaging unit /M Imaging unit /Y Toner cartridge /C Toner cartridge /M Toner cartridge /Y Toner empty sensor/C (PZS/C) Toner empty sensor/M (PZS/M) Toner empty sensor/Y (PZS/Y) Toner supply motor/Y (M9) Toner supply motor/M (M10) Toner supply motor/C (M11) Toner cartridge motor Y/M (M13) Toner cartridge motor C/K (M14) Printer control board (PRCB).
When sampling data is determined in TC ratio calculation control, TCR sensor output is higher than a predetermined value for a predetermined number of times in a row even though there is toner in the sub hopper.Right click that icon and select Printing preferences.
Wait a couple of minutes and in Devices and printers should be a new Magicard icon.
0 kommentar(er)
